HCPSLine12

Two 40G/OTU3 optical ports, and one pluggable 100G/OTU4 optical port. It supports a maximum of 100G SDH/OTN backhaul. The card can be configured as transponder (at 10G) and muxponder (at 100G line side) card. The 100G port P1 supports 100G Coherent DWDM CFP and non-coherent CFP. The 40G ports P2 and P3 are of QSFP+ types. The 10G ports P4 to P13 are of SFP+ types. This card is supported in TJ1600 Type-11SR, TJ1600 Type-6SR and TJ1600 Type-2SR chassis.

HCPSLine12 card supports CFP (P1), 2xQSFP+ (P2 and P3), 10xSFP+ (P4 to P13) interfaces.

The mode(s) supported with OSMC01, HCPXCC03, HCPXCC04 and OAMC include:

10x10G TO 1xOTU4 MUXPONDER -> P1: OTU4 + P4 to P13: STM-64/OTU2/OTU2e/10GE

NOTE 1: The 40G/OTU3 ports P2 and P3 are not supported in this product release.

NOTE 2: HCPSLine12 card can only be configured in muxponder mode in this product release. On the Node WUI, the card can be configured in 10x10G TO 1xOTU4 MUXPONDER mode.

Following is a schematic of the traffic configuration with POTP configuration:

Block diagram of traffic of HCPSLine10 in POTP configuration

The HCPSLine12 card also supports 10G and 40G Client to 1xOTU4 muxponder configurations as described earlier. The client side supports SFP+/QSFP+ optical interface and the line/network side supports CFP.

Following functionalities in particular are supported:

10x10GE/STM-64/OTU2 ->1xOTU4 (with E/GFEC/SD-FEC)
2x10GE/STM-64/OTU2+2x40GE/OTU3 ->1xOTU4 (E/GFEC/SD-FEC)

Following is a schematic of the traffic configuration in DWDM configuration:

Block diagram of traffic of HCPSLine10 in DWDM muxponder configuration

Front panel

Following figure shows the front panel view of HCPSLine12 card:

Front Panel View- HCPSLine12 Card

Power specifications

Power specifications- HCPSLine12

Specification	Range
Input Voltage	-48V DC
Maximum Power consumption	120W

Visual indicator details

The visual indicators on the HCPSLine12 card include two LEDs, the Active and the Status LEDs.

Possible LED status and their significance- HCPSLine12

Card State	Status LED	Active LED
Card initialization: State before the card initialize is complete on card insertion	Amber (Steady)	Amber (Steady)
Card in service: Initialization complete and card in service	Green (Steady)	Green (Steady)
Card mis-match: Network Element has already configured the slot with some other card	Amber	Amber
Card failed during boot up	Red	Amber
Card failed while in-service	Red	Green
Improper jack in of the card	Green (Blinking)	Green (Blinking)
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next	Amber	Amber
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next	Green	Green

CFP port visual indications

CFP Port Transmitter (Tx) and Receiver (Rx) LED Status- HCPSLine12

State	Rx LED	Tx LED
CFP present (Laser on) with Rx LOS	Amber	Green
CFP present (Laser off) with Rx LOS	Amber	Off
CFP present (Laser on) with no Rx LOS	Green	Green
CFP present (Laser off) with no Rx LOS	Green	Off
Card failed while in-service	Red	Green
CFP missing (LOS detected), Laser On (attempted)	Amber	Green
CFP missing (LOS masked since XFP missing and set to Admin_down), Laser Off (attempted)	Amber	Off
CFP failed (whether provisioned, unprovisioned, LOS or no LOS)	Red	Red

SFP+ port visual indications

SFP+ Port Transmitter (Tx) and Receiver (Rx) LED Status- HCPSLine12

State	Rx LED	Tx LED
SFP+/QSFP+ present (Laser on) with Rx LOS	Amber	Green
SFP+/QSFP+ present (Laser off) with Rx LOS	Amber	Off
SFP+/QSFP+ present (Laser on) with no Rx LOS	Green	Green
SFP+/QSFP+ present (Laser off) with no Rx LOS	Green	Off
Card failed while in-service	Red	Green
SFP+/QSFP+ missing (LOS detected), Laser On (attempted)	Amber	Green
SFP+/QSFP+ missing (LOS masked since SFP missing and set to Admin_down), Laser Off (attempted)	Amber	Off
SFP+/QSFP+ failed (whether provisioned, unprovisioned, LOS or no LOS)	Red	Red

LASER types

Supported Laser Types- HCPSLine12

Optics	Rate	Reach (Km)*

10GE SFP+	10Gbps	10 km
S64.2b SFP+	STM-64	40 km
P1L1-2D2 SFP+	STM-64/OTU2	80 km
DWDM Fixed/Tunable SFP+	10Gbps/STM-64/OTU2	80 km
QSFP+	40GE/OTU3	10 km
CFP	100GBASE-SR10/OTU4	100m
CFP	100GBASE-LR4/OTU4	10 km
CFP	100GBASE-ER4/OTU4	40 km
CFP Coherent	100GE/OTU4	80 km
CFP Coherent	100GE/OTU4	~1000 km (amplified)
* For G.652 fiber under Standard link conditions

Functional description

HCPSLine12 card supports the following functional features:

Processes the received OTU2/OTU2e/STM64/10GE, 40GE/OTU3 and OTU4/100GE frame for all alarm and performance monitoring signals.
Status and Active LEDs are provided to indicate the power on and working status of the card. Two LEDs for each optical port is used for transmitter and receiver laser status.
This card supports live insertion and hot-swap capability.