OFA-C-S26-FG/OFA-C-S23-FG

OFA-C-S26-FG/OFA-C-S23-FG provides a high output power of up to 26/23dBm. This enables longer reach spans for high loss networks. This 26/23dBm EDFA is housed in a standalone 1 RU 19’’ sub-rack which can be used along with this node. OFA-C-S26-FG/OFA-C-S23-FG has redundant -48V DC power supply unit.

This unit can be interfaced to Element Management Software (EMS) as standalone unit or integrated through the systems using the RJ45 NMS port. This card is supported in TJ1600 Type-11SR, TJ1600 Type-6SR chassis and TJ1600 Type-2SR chassis.

OPTICAL SAFETY: This unit can emit high laser powers up to 400mW (26dBm). If exposed directly, this high power is hazardous to skin and eyes and can cause blindness.

Front Panel

The following figure shows the front panel view of OFA-C-S26-FG/OFA-C-S23-FG card:

Power Specifications

Power Specifications- OFA-C-S26-FG/OFA-C-S23-FG Card

Visual Indicator Details

The visual indicators on the OFA-C-S26-FG/OFA-C-S23-FG card include four LEDs namely POWER, Input, EDFA, and Fan.

Possible LED status and their significance – OFA-C-S26-FG/OFA-C-S23-FG Card

LAN Interface

The LAN Interface provides a CSMA/CD based LAN transceiver of an Ethernet link. This is available as an RJ-45 connector. The Ethernet address is available in the non-volatile memory on the OAM card.

The LAN interface physical layer is completely implemented in hardware. The physical layer device provides clock recovery, bit timing, equalization and a ‘Jabber’ circuit. The Media Access Control (MAC) function is implemented in software available as part of the microcontroller. ‘Jabber’ circuitry ensures that the transmitter does not hold up the interface for more than a full frame of data.

The LAN interface is associated with two LEDs namely Green and Amber that are used to indicate link status of the connector.

LAN interface can be connected directly to the element management software and can be connected to the available NMS port on the systems.

Possible LED status and their significance - OFA-C-S26-FG/OFA-C-S23-FG

External Alarms Interface

The OFA-C-S26-FG/OFA-C-S23-FG card provides seven external alarm outputs.

OFA-C-S26-FG/OFA-C-S23-FG can export 7 alarm signals to the system through a standard RJ45 interface. These alarm signals are Power Supply A Alarm, Power Supply B Alarm, Input Power Alarm, Output Power Alarm, Pump Current Alarm, Pump Temperature, and Module Temperature.

Different output alarm types

OFA-C-S26-FG/OFA-C-S23-FG Card operating modes

OFA-C-S26-FG/OFA-C-S23-FG is a fixed very low gain EDFA that gives a high output power of the order of 26/23 dBm.

Fixed Gain OFA Card Types

There are two operating modes supported:

• Automatic Gain control mode: In this mode, the EDFA is operated at the designed flat gain. Gain feedback controller is active in this mode. This mode enables to add the new channels without affecting the existing channel power.
• Automatic Power control mode: In this mode, EDFA is set to operate at a constant power output, irrespective of the input power. Transient controller is not active in this mode.

OFA-C-S26-FG/OFA-C-S23-FG is used for optical amplification in POTP and DWDM configuration of the system.

The schematic diagram of the connectivity of the OFA-C-S26-FG/OFA-C-S23-FG card is as follows:

In general, OFA-C-S26-FG/OFA-C-S23-FG is followed by OFA cards to boost the incoming signal strength in order to get the rated output power of 26dBm as the gain in this EDFA is very low (in the order of 6-8dB).

Typical Specifications

Typical specifications of the high power OFA are as follows:

• Card supports APR functionality.
• Support C-band DWDM amplification.
• Output monitor port of with 1% tap.
• Support for AGC mode and optional APC operating modes.
• Supports NMS port.
• Supports hardware alarm interface for EDFA specific alarms.
• Supports redundancy on -48V DC input supply voltage.
• Meet Class 1M safety requirements.

The following table summarizes different parameters of Fixed Gain OFA card and its typical values.

Fixed Gain OFA Card parameters and typical values