|
|
|
|
HCPSLine26 is a single slot card providing interface to 20x10G client ports and 1x100G/200G software configurable optical line port. The coherent optics on the card is included as part of the card and is not pluggable. This card is supported in TJ1600 POTP (11 slot), TJ1600 Type-6SR and TJ1600 Type-2SR chassis.
The line rate of HCPSLine26 is software configurable to either 100G or 200G. 100G line rate is over QPSK modulation while 200G line-rate is supported on both 8-QAM and 16-QAM modulations.
The mode supported with HCPXCC03, HCPXCC04, OSMC01 and OAMC include:
20x10G to 2 OTU4 Muxponder: Ports P1 supports 100G (OTUC1)/ 200G (OTU2) and Ports P2-P21 support STM64/10GE/OTU2/OTU2e/8GFC/12GFC
The following figure shows the front panel view of the HCPSLine26 card:
Power Specifications - HCPSLine26
Specification |
Range |
|---|---|
Input Voltage |
-48V |
Maximum Power consumption |
135W |
The visual indicators on the HCPSLine26 card include two LEDs, the Active and the Status.
Possible LED status and their significance- HCPSLine26
Card State |
Status LED |
Active LED |
|---|---|---|
Card initialization: State before the card initialize is complete on card insertion. |
Amber (Steady) |
Amber (Steady) |
Card in service: Initialization complete and card in service. |
Green (Steady) |
Green (Steady) |
Card mis-match: Node has already configured the slot with some other card. |
Amber |
Amber |
Card failed during boot up. |
Red |
Amber |
Card failed while in-service. |
Red |
Green |
Improper jack-in of the card. |
Green (Blinking) |
Green (Blinking) |
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next. |
Amber |
Amber |
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next. |
Green |
Green |
Early Ejector LED status: One ejector is removed (contains one ejector switch in right) |
OFF |
Amber |
CFP2 Port Transmitter (Tx) and Receiver (Rx) LED Status - HCPSLine26
State |
Rx LED |
Tx LED |
|---|---|---|
Laser on with Rx LOS. |
Amber |
Green |
Laser off with Rx LOS |
Amber |
Off |
Laser on with no Rx LOS. |
Green |
Green |
Laser off with no Rx LOS. |
Green |
Off |
Supported Laser Types- HCPSLine26
Optics |
Rate |
Reach* |
|
|---|---|---|---|
10GE SFP+ |
10Gbps/Lan PHY |
10km |
|
S64.2b SFP+ |
STM-64/Wan PHY |
40km |
|
P1L1-2D2 SFP+ |
STM-64/OTU2 |
80km |
|
Onboard optics |
Configurable 100G/200G |
100G- 2500Km (amplified) 200G- 1200Km (amplified) |
|
* For G.652 fiber under Standard link conditions |
|||
Specification |
CFP2 - 100G- Differential Encoding |
CFP2 - 100G- Non-Differential Encoding |
CFP2 - 200G- 8-QAM |
CFP2 - 200G- 16-QAM |
|---|---|---|---|---|
Modulation Type |
DP-DQPSK |
DP-QPSK |
DP-QPSK |
DP-QPSK |
Transmitter Tunable Range |
191.25 Thz to 196.10 Thz |
191.25 Thz to 196.10 Thz |
191.25 Thz to 196.10 Thz |
191.25 Thz to 196.10 Thz |
Minimum Output Power |
-15 dBm |
-15 dBm |
-15 dBm |
-15 dBm |
Maximum Output Power |
+1 dBm |
+1 dBm |
+1 dBm |
+1 dBm |
Receiver Sensitivity at Low OSNR Scenario |
-18 dBm |
-18 dBm |
-18 dBm |
-18 dBm |
Receiver Sensitivity at High OSNR Scenario |
-29 dBm |
-30 dBm |
-24 dBm |
-22 dBm |
Receiver Overload |
0 dBm |
0 dBm |
0 dBm |
0 dBm |
OSNR Cutoff (at 0.1nmRBW) |
13.5 dB |
11.5 dB |
18 dB |
21 dB |
FEC Types |
G.709, EFEC, SD-FEC |
G.709, EFEC, SD-FEC |
G.709, EFEC, SD-FEC |
G.709, EFEC, SD-FEC |
Chromatic Dispersion Limit |
40,000 ps/nm |
40,000 ps/nm |
20,000 ps/nm |
16,000 ps/nm |
PMD Tolerance |
30 ps |
30 ps |
15 ps |
15 ps |
HCPSLine26 card supports the following functional features: