|
|
|
|
HCPSLine22 card supports a maximum of 100G OTN backhaul. The interface of this card is 1x100G (P11) for CFP and 10x10G (P1 to P10) for SFP+.
The following modes are supported in TJ1600 Type-11SR:
HCPXCC03 |
HCPXCC04 |
OSMC01 |
|---|---|---|
10x10G TO 1xOTU4 MUXPONDER
5X10G TXP with eFEC and gFEC:
|
10x10G SDH FLEXI
1x100G OTN TRIBUTARY
10x10G OTN TRIBUTARY with eFEC and gFEC
10x10G TO 1xOTU4 MUXPONDER
5X10G TXP with eFEC and gFEC:
|
10x10G TO 1xOTU4 MUXPONDER
5X10G TXP with eFEC and gFEC:
|
The following modes are supported in TJ1600 Type-6SR:
TJ1600 Type-6SR modes
200G Mode |
400G Mode |
|---|---|
10X10G FLEXI TRIBUTARY AND CROSS-CONNECT with eFEC and gFEC:
NOTE: 8GFC is supported only with gFEC. This mode is supported only in Slot1 and Slot2. |
10x10G 1x100G TRIBUTARY AND CROSS-CONNECT:
NOTE: This mode is supported only in Slot1 and Slot2. |
10x10G TO 1xOTU4 MUXPONDER
|
10x10G TO 1xOTU4 MUXPONDER
|
5X10G TXP with eFEC and gFEC
|
5X10G TXP with eFEC and gFEC
|
The following modes are supported in TJ1600 Type-2SR:
TJ1600 Type-2SR modes
200G Mode |
400G Mode |
|---|---|
10X10G FLEXI TRIBUTARY AND CROSS-CONNECT with eFEC and gFEC:
NOTE: 8GFC is supported only with gFEC. |
10x10G 1x100G TRIBUTARY AND CROSS-CONNECT:
|
NOTE: Lower order client types (STM1/STM4/STM16/1GE/1GFC/2GFC) are not supported in 400G mode.
Following is a schematic of the traffic configuration with OTN configuration:
The HCPSline22 card also can be configured as 10G transponder and regenerator cards:
Following is a schematic of the traffic configuration in DWDM configuration:
The HCPSLine22 card also supports 10G and 100G Client to 1xOTU4 muxponder configurations.
Following functionalities in particular are supported:
10x10G TO 1xOTU4 MUXPONDER-> 1xOTU4 + 10xSTM-64/10GE/OTU2/OTU2e
Following is a schematic of the traffic configuration in DWDM configuration:
Following figure shows the front panel view of HCPSLine22 card:
Power specifications - HCPSLine22
Specification |
Range |
|---|---|
Input Voltage |
-48V DC |
Maximum Power consumption |
130 W |
The visual indicators on the HCPSLine22 card include two LEDs, the Active and the Status.
Possible LED status and their significance - HCPSLine22
Card State |
Status LED |
Active LED |
|---|---|---|
Card initialization: State before the card initialize is complete on card insertion. |
Amber (Steady) |
Amber (Steady) |
Card in service: Initialization complete and card in service. |
Green (Steady) |
Green (Steady) |
Card mis-match: Network Element has already configured the slot with some other card. |
Amber |
Amber |
Card failed during boot up. |
Red |
Amber |
Card failed while in-service. |
Red |
Green |
Improper jack in of the card. |
Green (Blinking) |
Green (Blinking) |
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next. |
Amber |
Amber |
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next. |
Green |
Green |
CFP Port Transmitter (Tx) and Receiver (Rx) LED Status - HCPSLine22
State |
Rx LED |
Tx LED |
|---|---|---|
CFP present (Laser on) with Rx LOS. |
Amber |
Green |
CFP present (Laser off) with Rx LOS. |
Amber |
Off |
CFP present (Laser on) with no Rx LOS. |
Green |
Green |
CFP present (Laser off) with no Rx LOS. |
Green |
Off |
Card failed while in-service. |
Red |
Green |
CFP missing (LOS detected), Laser On (attempted). |
Amber |
Green |
CFP missing (LOS masked since SFP missing and set to Admin_down), Laser Off (attempted). |
Amber |
Off |
CFP failed (whether provisioned, unprovisioned, LOS or no LOS). |
Red |
Red |
SFP+ Port Transmitter (Tx) and Receiver (Rx) LED Status- HCPSLine12
State |
Rx LED |
Tx LED |
|---|---|---|
SFP+ present (Laser on) with Rx LOS |
Amber |
Green |
SFP+ present (Laser off) with Rx LOS |
Amber |
Off |
SFP+ present (Laser on) with no Rx LOS |
Green |
Green |
SFP+ present (Laser off) with no Rx LOS |
Green |
Off |
Card failed while in-service |
Red |
Green |
SFP+ missing (LOS detected), Laser On (attempted) |
Amber |
Green |
SFP+ missing (LOS masked since SFP missing and set to Admin_down), Laser Off (attempted) |
Amber |
Off |
SFP+ failed (whether provisioned, unprovisioned, LOS or no LOS) |
Red |
Red |
Supported Laser Types - HCPSLine22
Optics |
Rate |
Reach (Km)* |
|---|---|---|
10GE SFP+ |
10Gbps |
10km |
S64.2b SFP+ |
STM-64 |
40km |
P1L1-2D2 SFP+ |
STM-64/OTU2 |
80km |
DWDM Fixed/Tunable SFP+ |
10Gbps/STM-64/OTU2 |
80km |
CFP |
100GBASE-SR10/OTU4 |
100m |
CFP |
100GBASE-LR4/OTU4 |
10km |
CFP |
100GBASE-ER4/OTU4 |
40km |
CFP Coherent |
100GE/OTU4 |
~2500km (amplified) |
* For G.652 fiber under Standard link conditions |
||
HCPSLine22 card supports the following functional features: