|
|
|
|
HCPSLine08 card supports 2 XFP and 16 SFP interfaces. The card is supported in TJ1600 Type-11SR, TJ1600 Type-6SR and TJ1600 Type-2SR chassis.
The mode(s) supported with HCPXCC03 in TJ1600 Type-11SR chassis include:
The mode(s) supported with HCPXCC04 in TJ1600 Type-11SR chassis include:
The mode(s) supported with OSMC01 card in TJ1600 Type-11SR and TJ1600 Type-6SR chassis include:
IntraCard TRANS/MUXPONDER -> P1 and P2: OTU2 + P3 to P10: STM-16/OTU1 or P3 to P18: STM-1/4/1GE
The mode(s) supported with OAMC card in TJ1600 Type-2SR chassis include:
IntraCard TRANS/MUXPONDER -> P1 and P2: OTU2 + P3 to P10: STM-16/OTU1 or P3 to P18: STM-1/4/1GE
NOTE 1: In OTN FlexiCard or IntraCard TRANS/MUXPONDER mode, if P3 to P10 ports are configured as STM-16, then remaining ports (P11 to P18) cannot be used.
NOTE 2: With HCPXCC04, fresh card configuration is not supported for SDH GATEWAY Card mode.
Following figure shows the front panel view of HCPSLine08 card:
Power specifications- HCPSLine08
Specification |
Range |
|---|---|
Input Voltage |
-48V DC |
Power consumption |
100W |
The visual indicators on the HCPSLine08 card include two LEDs, the ACTIVE and the STATUS LEDs.
Possible LED status and their significance- HCPSLine08
Card State |
Status LED |
Active LED |
|---|---|---|
Card initialization: State before the card initialize is complete on card insertion. |
Amber (Steady) |
Amber (Steady) |
Card in service: Initialization complete and card in service. |
Green (Steady) |
Green (Steady) |
Card mis-match: Node has already configured the slot with some other card. |
Amber |
Amber |
Card failed during boot up. |
Red |
Amber |
Card failed while in-service. |
Red |
Green |
Improper jack in of the card |
Green (Blinking) |
Green (Blinking) |
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next. |
Amber |
Amber |
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next. |
Green |
Green |
Early Ejector LED status: One ejector is removed (contains one ejector switch in right). |
OFF |
Amber |
SFP/XFP Port Transmitter (Tx) and Receiver (Rx) LED Status- HCPSLine08
State |
Rx LED |
Tx LED |
|---|---|---|
SFP/XFP present (Laser on) with Rx LOS. |
Amber |
Green |
SFP/XFP present (Laser off) with Rx LOS. |
Amber |
Off |
SFP/XFP present (Laser on) with no Rx LOS. |
Green |
Green |
SFP/XFP present (Laser off) with no Rx LOS. |
Green |
Off |
Card failed while in-service. |
Red |
Green |
SFP/XFP missing (LOS detected), Laser On (attempted). |
Amber |
Green |
SFP/XFP missing (LOS masked since XFP missing and set to Admin_down), Laser Off (attempted). |
Amber |
Off |
SFP/XFP failed (whether provisioned, unprovisioned, LOS or no LOS). |
Red |
Red |
The LASER types supported are:
OPTICAL SAFETY: Do not stare or look directly into the optical connector output beam, as this can cause irreparable damage to your eyes and even loss of eye sight.
HCPSLine08 card processes the received GE/STM-16/STM-64 frame for all alarms and performance monitoring signals.
HCPSLine08 card supports the following functional features: