HCPULine01

HCPULine01 card supports 20xSTM-1/4 or 8xSTM-16 or 16x1GE (excluding P5, P10, P15, P20) interfaces. The ports are divided into 4 groups of 5 SFPs each. Each port group is independently configurable and supports a backhaul capacity of 5G. Total capacity of the card is 20G.

STM-16 line rate is supported on ports P1, P5, P6, P10, P11, P15, P16, and P20.

NOTE: Some long haul SFPs will not measure receive power beyond (-8.5 dBm). Hence before connecting long haul LASERs, check with the optical power meter.

The mode(s) supported with HCPXCC03, HCPXCC04 include:

HCPULine01 card supports the following functional features:

Pointer processing, performance monitoring and POH termination.
Overhead bytes tunneling from different optical interfaces across the base chassis.
SDH data path which has independent ADD and DROP capacity to support both unidirectional and bi-directional cross-connects live insertion.

Front panel

The front panel view of HCPULine01 card is shown below.

Front Panel View- HCPULine01 Card

Power specifications

HCPULine01 - Power specification

Parameter	Specification
Input voltage	-48V DC
Maximum Power consumption	80W

Visual indicator details

The visual indicators on the HCPULine01 card include two LEDs namely ACT (Active) and STS (Status) on the front panel to indicate the status of the card and the port LEDs.

HCPULine01 - Active and status LEDs indications

Card State	Status LED	Active LED
Card initialization: State before the card initialize is complete on card insertion.	Amber (Steady)	Amber (Steady)
Card in service: Initialization complete and card in service.	Green (Steady)	Green (Steady)
Card mis-match: Node has already configured the slot with some other card.	Amber	Amber
Card failed during boot up.	Red	Amber
Card failed while in-service.	Red	Green
Improper jack in of the card	Green (Blinking)	Green (Blinking)
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next.	Amber	Amber
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next.	Green	Green
Early Ejector LED status: One ejector is removed (contains one ejector switch in right)	OFF	Amber

HCPULine01 - SFP Port Transmitter (Tx) and Receiver (Rx) LED Status

State	Rx LED	Tx LED
SFP present (LASER on) with Rx LOS	Amber	Green
SFP present (LASER off) with Rx LOS	Amber	Off
SFP present (LASER on) with no Rx LOS	Green	Green
SFP present (LASER off) with no Rx LOS	Green	Off
Card failed while in-service.	Red	Green
SFP missing (LOS detected), LASER On (attempted)	Amber	Green
SFP missing (LOS masked since SFP missing and set to Admin_down), LASER Off (attempted)	Amber	Off
SFP failed (whether provisioned, unprovisioned, LOS or no LOS)	Red	Red

LASER types

The LASER types supported in STM-1, STM-4 and STM-16 interfaces include:

STM-1: S-1.1, L-1.1 and L-1.2
STM-4: S-4.1, L-4.1 and L-4.2
STM-16: S-16.2, L-16.1 and L-16.2

NOTE: Some long haul SFPs do not measure receive power beyond (-8.5 dBm). Therefore, before connecting long haul LASERs, check the receive power with the optical power meter.