HCPSLine22

HCPSLine22 card supports a maximum of 100G OTN backhaul. It supports interfaces of 1x100G (P11) with CFP and 10x10G (P1 to P10) with SFP+.

HCPSLine22 card supports the following functional features:

It provides 10x10G SDH/10G client to network cross-connect.
Card supports live insertion and hot-swap capability.
Support for +/- 60PPM offset on OTU2/OTU2e interfaces.

Front panel

Following figure shows the front panel view of HCPSLine22 card:

Front Panel View- HCPSLine22 Card

Power specifications

HCPSLine22 - Power specifications

Specification	Range
Input Voltage	-48V DC
Maximum Power consumption	140 W

HCPSLine22 supports following modes:

10x10G TO 1xOTU4 MUXPONDER

P1 to P10: STM-64/10GE/OTU2/OTU2e
P11: OTU4

10x10G SDH FLEXI

P1 to P10: STM-64/10GE

1x100G OTN TRIBUTARY

P11: 100GE/OTU4

10x10G OTN TRIBUTARY with eFEC and gFEC

P1 to P10: STM-64/10GE/OTU2/OTU2e/8GFC
NOTE: 8GFC is supported only with gFEC mode.

5X10G TXP with eFEC and gFEC

P1 to P5: OTU2/OTU2e/OTU1f
P6 to P10: STM-64/10GE/OTU2/OTU2e/OTU1f/8GFC/12GFC

10X10G FLEXI TRIBUTARY AND CROSS-CONNECT with eFEC and gFEC

Ports P1, P2, P7 and P9: OTU2/OTU2e/10GE/1GE/STM64/STM16/STM4/STM1/1GFC/2GFC/4GFC/8GFC
Ports P3, P4, P5, P6, P8 and P10: 10GE/1GE/STM64/STM16/STM4/STM1/1GFC/2GFC/4GFC/8GFC
NOTE: 8GFC is supported only with gFEC.

In TJ1600-6 system, this mode is supported in slots 1 and 2.

10x10G 1x100G TRIBUTARY AND CROSS-CONNECT

Ports P1 to P10: STM64/10GELAN/OTU2/OTU2e/8GFC
P11: OTU4
NOTE: In TJ1600-6 system, this mode is supported in slots 1 and 2.

HCPSLine22 modes supported in TJ1600-11

HCPXCC03	HCPXCC04	OSMC01
10x10G TO 1xOTU4 MUXPONDER 5X10G TXP with eFEC and gFEC	10x10G SDH FLEXI 1x100G OTN TRIBUTARY 10x10G OTN TRIBUTARY with eFEC and gFEC 10x10G TO 1xOTU4 MUXPONDER 5X10G TXP with eFEC and gFEC	10x10G TO 1xOTU4 MUXPONDER 5X10G TXP with eFEC and gFEC

HCPSLine22 modes supported in TJ1600-6

200G Mode	400G Mode
10X10G FLEXI TRIBUTARY AND CROSS-CONNECT with eFEC and gFEC 10x10G TO 1xOTU4 MUXPONDER 5X10G TXP with eFEC and gFEC	10x10G 1x100G TRIBUTARY AND CROSS-CONNECT 10x10G TO 1xOTU4 MUXPONDER 5X10G TXP with eFEC and gFEC

HCPSLine22 modes supported in TJ1600-2

200G Mode	400G Mode
10X10G FLEXI TRIBUTARY AND CROSS-CONNECT with eFEC and gFEC 5X10G TXP with eFEC and gFEC	10x10G 1x100G TRIBUTARY AND CROSS-CONNECT 5X10G TXP with eFEC and gFEC

NOTE: Lower order client types (STM1/STM4/STM16/1GE/1GFC/2GFC) are not supported in 400G mode.

OTN Configuration

1x100G OTN TRIBUTARY
10x10G OTN TRIBUTARY with eFEC and gFEC

Following is a schematic of the traffic configuration with OTN configuration:

Block diagram of traffic of HCPSLine10 in POTP configuration

Transponder Configuration

The HCPSline22 card also can be configured as 10G transponder and regenerator cards:

5X10G TXP -> 5xOTU2/OTU2e/OTU1f

Following is a schematic of the traffic configuration in DWDM configuration:

Block diagram of traffic of HCPSLine22 in DWDM transponder configuration

Muxponder Configuration

The HCPSLine22 card also supports 10G and 100G Client to 1xOTU4 muxponder configurations.

Following functionalities in particular are supported:

10x10G TO 1xOTU4 MUXPONDER

Following is a schematic of the traffic configuration in DWDM configuration:

Capture11

Visual indicator details

The visual indicators on the HCPSLine22 card has two LEDs - the Sts (Status) LED indicate the status of the card and the Act (Active) LED indicates whether the card is active or not

HCPSLine22 - Active and status LEDs indications

Card State	Status LED	Active LED
Card initialization: State before the card initialize is complete on card insertion.	Amber (Steady)	Amber (Steady)
Card in service: Initialization complete and card in service.	Green (Steady)	Green (Steady)
Card mis-match: Network Element has already configured the slot with some other card.	Amber	Amber
Card failed during boot up.	Red	Amber
Card failed while in-service.	Red	Green
Improper jack in of the card.	Green (Blinking)	Green (Blinking)
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next.	Amber	Amber
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next.	Green	Green

HCPSLine22 - CFP Port LED indications

State	Rx LED	Tx LED
CFP present (LASER on) with Rx LOS.	Amber	Green
CFP present (LASER off) with Rx LOS.	Amber	Off
CFP present (LASER on) with no Rx LOS.	Green	Green
CFP present (LASER off) with no Rx LOS.	Green	Off
Card failed while in-service.	Red	Green
CFP missing (LOS detected), LASER On (attempted).	Amber	Green
CFP missing (LOS masked since SFP missing and set to Admin_down), LASER Off (attempted).	Amber	Off
CFP failed (whether provisioned, unprovisioned, LOS or no LOS).	Red	Red

HCPSLine22 - SFP+ Port LED indications

State	Rx LED	Tx LED
SFP+ present (LASER on) with Rx LOS	Amber	Green
SFP+ present (LASER off) with Rx LOS	Amber	Off
SFP+ present (LASER on) with no Rx LOS	Green	Green
SFP+ present (LASER off) with no Rx LOS	Green	Off
Card failed while in-service	Red	Green
SFP+ missing (LOS detected), LASER On (attempted)	Amber	Green
SFP+ missing (LOS masked since SFP missing and set to Admin_down), LASER Off (attempted)	Amber	Off
SFP+ failed (whether provisioned, unprovisioned, LOS or no LOS)	Red	Red

LASER types

HCPSLine22 - Supported LASER types

Optics	Rate	Reach (Km)*

10GE SFP+	10Gbps	10km
S64.2b SFP+	STM-64	40km
P1L1-2D2 SFP+	STM-64/OTU2	80km
DWDM Fixed/Tunable SFP+	10Gbps/STM-64/OTU2	80km
CFP	100GBASE-SR10/OTU4	100m
CFP	100GBASE-LR4/OTU4	10km
CFP	100GBASE-ER4/OTU4	40km
CFP Coherent	100GE/OTU4	~2500km (amplified)
* For G.652 fiber under Standard link conditions