HCPSLine12 card supports ten pluggable 10G/OTU2 optical ports, two pluggable 40GE/OTU3 optical ports, and one pluggable 100G/OTU4 optical port. The 40G ports P2 and P3 are of QSFP+ types. The 10G ports P4 to P13 are of SFP+ types.
NOTE: OTU3 optical ports are not supported.
HCPSLine12 card supports CFP (P1), 1xQSFP+/QSFP28 (P2), 1xQSFP+ (P3), and 10xSFP+ (P4 to P13) interfaces.
HCPSLine12 card supports the following functional features:
The mode(s) supported include:
NOTE: If a port “n” is configured as 16GFC then immediate next port (n+1) cannot be used for any other client ports.
If a port “m” is configured as 32GFC then next 3 continuous ports (m+1, m+2 & m+3) cannot be used for any other client ports.
Following is a schematic of the traffic configuration with POTP configuration:
The HCPSLine12 card also supports 10G and 40G Client to 1xOTU4 muxponder configurations as described earlier. The client side supports SFP+/QSFP+ optical interface and the line/network side supports CFP.
Following functionalities in particular are supported:
Following is a schematic of the traffic configuration in DWDM configuration:
Front panel
Following figure shows the front panel view of HCPSLine12 card:
Power specifications
Specification |
Range |
---|---|
Input Voltage |
-48V DC |
Maximum Power consumption |
130 W |
Visual indicator details
The visual indicators on the HCPSLine12 card has two LEDs - the Sts (Status) LED indicate the status of the card and the Act (Active) LED indicates whether the card is active or not.
Card State |
Status LED |
Active LED |
---|---|---|
Card initialization: State before the card initialize is complete on card insertion |
Amber (Steady) |
Amber (Steady) |
Card in service: Initialization complete and card in service |
Green (Steady) |
Green (Steady) |
Card mis-match: Network Element has already configured the slot with some other card |
Amber |
Amber |
Card failed during boot up |
Red |
Amber |
Card failed while in-service |
Red |
Green |
Improper jack in of the card |
Green (Blinking) |
Green (Blinking) |
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next |
Amber |
Amber |
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next |
Green |
Green |
State |
Rx LED |
Tx LED |
---|---|---|
CFP present (LASER on) with Rx LOS |
Amber |
Green |
CFP present (LASER off) with Rx LOS |
Amber |
Off |
CFP present (LASER on) with no Rx LOS |
Green |
Green |
CFP present (LASER off) with no Rx LOS |
Green |
Off |
Card failed while in-service |
Red |
Green |
CFP missing (LOS detected), LASER On (attempted) |
Amber |
Green |
CFP missing (LOS masked since XFP missing and set to Admin_down), LASER Off (attempted) |
Amber |
Off |
CFP failed (whether provisioned, unprovisioned, LOS or no LOS) |
Red |
Red |
State |
Rx LED |
Tx LED |
---|---|---|
SFP+/QSFP+ present (LASER on) with Rx LOS |
Amber |
Green |
SFP+/QSFP+ present (LASER off) with Rx LOS |
Amber |
Off |
SFP+/QSFP+ present (LASER on) with no Rx LOS |
Green |
Green |
SFP+/QSFP+ present (LASER off) with no Rx LOS |
Green |
Off |
Card failed while in-service |
Red |
Green |
SFP+/QSFP+ missing (LOS detected), LASER On (attempted) |
Amber |
Green |
SFP+/QSFP+ missing (LOS masked since SFP missing and set to Admin_down), LASER Off (attempted) |
Amber |
Off |
SFP+/QSFP+ failed (whether provisioned, unprovisioned, LOS or no LOS) |
Red |
Red |
State |
Rx LED |
Tx LED |
---|---|---|
QSFP28 present (LASER on) with Rx LOS. |
Amber |
Green |
QSFP28 present (LASER off) with Rx LOS. |
Amber |
Off |
QSFP28 present (LASER on) with no Rx LOS. |
Green |
Green |
QSFP28 present (LASER off) with no Rx LOS. |
Green |
Off |
Card failed while in-service. |
Red |
Green |
QSFP28 missing (LOS detected), LASER On (attempted). |
Amber |
Green |
QSFP28 missing (LOS masked since SFP missing and set to Admin_down), LASER Off (attempted). |
Amber |
Off |
QSFP28 failed (whether provisioned, unprovisioned, LOS or no LOS). |
Red |
Red |
LASER types
Optics |
Rate |
Reach (Km)* |
---|---|---|
QSFP28 |
100GBASE-LR4/OTU4 |
10km |
QSFP28 |
100GBASE-ER4-Lite |
25km NOTE: Reach can be upto 40km with on-board FEC. |
10GE SFP+ |
10Gbps |
10 km |
S64.2b SFP+ |
STM-64 |
40 km |
P1L1-2D2 SFP+ |
STM-64/OTU2 |
80 km |
DWDM Fixed/Tunable SFP+ |
10Gbps/STM-64/OTU2 |
80 km |
QSFP+ |
40GE/OTU3 |
10 km |
CFP |
100GBASE-SR10/OTU4 |
100m |
CFP |
100GBASE-LR4/OTU4 |
10 km |
CFP |
100GBASE-ER4/OTU4 |
40 km |
CFP Coherent |
100GE/OTU4 |
80 km |
CFP Coherent |
100GE/OTU4 |
~2500 km (amplified) |
* For G.652 fiber under Standard link conditions |