|
|
|
|
HCPSLine08 card supports 2 XFP and 16 SFP interfaces. HCPSLine08 card processes the received GE/STM-16/STM-64 frame for all alarms and performance monitoring signals.
HCPSLine08 card supports the following functional features:
The mode(s) supported with HCPXCC03:
The mode(s) supported with HCPXCC04:
The mode(s) supported with OSMC01:
IntraCard TRANS/MUXPONDER -> P1 and P2: OTU2 + P3 to P10: STM-16/OTU1 or P3 to P18: STM-1/4/1GE
The mode(s) supported with OAMC:
IntraCard TRANS/MUXPONDER -> P1 and P2: OTU2 + P3 to P10: STM-16/OTU1 or P3 to P18: STM-1/4/1GE
NOTE 1: In OTN FlexiCard or IntraCard TRANS/MUXPONDER mode, if P3 to P10 ports are configured as STM-16, then remaining ports (P11 to P18) cannot be used.
NOTE 2: With HCPXCC04, fresh card configuration is not supported for SDH GATEWAY Card mode.
Front panel
Following figure shows the front panel view of HCPSLine08 card:
Power specifications
HCPSLine08 - Power specifications
Specification |
Range |
|---|---|
Input Voltage |
-48V DC |
Maximum Power consumption |
110W |
Visual indicator details
The visual indicators on the HCPSLine08 card has two LEDs - the Sts (Status) LED indicate the status of the card and the Act (Active) LED indicates whether the card is active or not.
HCPSLine08 - Active and status LEDs indications
Card State |
Status LED |
Active LED |
|---|---|---|
Card initialization: State before the card initialize is complete on card insertion. |
Amber (Steady) |
Amber (Steady) |
Card in service: Initialization complete and card in service. |
Green (Steady) |
Green (Steady) |
Card mis-match: Node has already configured the slot with some other card. |
Amber |
Amber |
Card failed during boot up. |
Red |
Amber |
Card failed while in-service. |
Red |
Green |
Improper jack in of the card |
Green (Blinking) |
Green (Blinking) |
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next. |
Amber |
Amber |
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next. |
Green |
Green |
Early Ejector LED status: One ejector is removed (contains one ejector switch in right). |
OFF |
Amber |
HCPSLine08 - SFP/XFP port LED indications
State |
Rx LED |
Tx LED |
|---|---|---|
SFP/XFP present (LASER on) with Rx LOS. |
Amber |
Green |
SFP/XFP present (LASER off) with Rx LOS. |
Amber |
Off |
SFP/XFP present (LASER on) with no Rx LOS. |
Green |
Green |
SFP/XFP present (LASER off) with no Rx LOS. |
Green |
Off |
Card failed while in-service. |
Red |
Green |
SFP/XFP missing (LOS detected), LASER On (attempted). |
Amber |
Green |
SFP/XFP missing (LOS masked since XFP missing and set to Admin_down), LASER Off (attempted). |
Amber |
Off |
SFP/XFP failed (whether provisioned, unprovisioned, LOS or no LOS). |
Red |
Red |
LASER types
The LASER types supported are: