HCPSLine27

HCPSLine27 is a single slot card providing interface to 10x10G and 2x100G client ports and 1x100G/200G software configurable optical line port. The coherent optics on the card is included as part of the card and is not pluggable.

The line rate of HCPSLine27 is software configurable to either 100G or 200G. 100G line rate is over QPSK modulation while 200G line-rate is supported on both 8-QAM and 16-QAM modulations.

HCPSLine27 card supports the following functional features:

Processes the received OTUC2/OTU4 frame for all alarm and performance monitoring signal.
Supports live insertion and hot-swap capability.

The mode(s) supported with HCPXCC03, HCPXCC04, OSMC01 and OAMC include:

10X10G to OTU4 Muxponder + Flexi 100G to OTU4 Transponder
- P1: 100G (OTUC1)/ 200G (OTUC2)
- P2 supports 100GE/OTU4
- P4 - P13: STM64/10GE/OTU2/OTU2e/8GFC/12GFC
- P5, P7, P9, P11: 16GFC
- P4, P8: 32GFC
  NOTE: If a port “n” is configured as 16GFC then immediate next port (n+1) cannot be used for any other client ports.
  
  If a port “m” is configured as 32GFC then next 3 continuous ports (m+1, m+2 & m+3) cannot be used for any other client ports.
Two Flexi 100G to 2 OTU4 Transponder
- P1: 100G (OTUC1)/200G (OTUC2)
- P2, P3: 100GE/OTU4

Front panel

Following figure shows the front panel view of HCPSLine27 card.

Front Panel View - HCPSLine27

Power specifications

HCPSLine27 - Power specifications

Specification	Range
Input Voltage	-48V DC
Maximum Power consumption	150 W

Visual indicator details

The visual indicators on the HCPSLine27 card has two LEDs - the Sts (Status) LED indicate the status of the card and the Act (Active) LED indicates whether the card is active or not.

HCPSLine27 - Active and status LEDs indications

Card State	Status LED	Active LED
Card initialization: State before the card initialize is complete on card insertion.	Amber (Steady)	Amber (Steady)
Card in service: Initialization complete and card in service.	Green (Steady)	Green (Steady)
Card mis-match: Node has already configured the slot with some other card.	Amber	Amber
Card failed during boot up.	Red	Amber
Card failed while in-service.	Red	Green
Improper jack-in of the card.	Green (Blinking)	Green (Blinking)
Hard Reset: All devices reset, FPGAs cleared and reprogrammed. Goes to initializing state next.	Amber	Amber
Soft Reset: Software is restarted, devices are reinitialized with provisioning. Goes to initializing state next.	Green	Green
Early Ejector LED status: One ejector is removed (contains one ejector switch in right)	OFF	Amber

HCPSLine27 - CFP2 Port LED indications

State	Rx LED	Tx LED
LASER on with Rx LOS.	Amber	Green
LASER off with Rx LOS	Amber	Off
LASER on with no Rx LOS.	Green	Green
LASER off with no Rx LOS.	Green	Off

LASER types

HCPSLine27 - Supported LASER types

Optics	Rate	Reach*

10GE SFP+	10Gbps/Lan PHY	10km
S64.2b SFP+	STM-64/Wan PHY	40km
P1L1-2D2 SFP+	STM-64/OTU2	80km
QSFP28	100GBASE-SR10/OTU4	100m
QSFP28	100GBASE-LR4/OTU4	10km
QSFP28	100GBASE-ER4-lite/OTU4	25km#
Onboard optics	Configurable 100G/200G	100G- 2500Km (amplified) 200G- 1200Km (amplified)
* For G.652 fiber under Standard link conditions
# ER4 Lite variant